外貿協會::五金展

MS-1 Touch Plus is an Ultrasonic Magneto Scaler, an upgrade from our MS-1 DUAL for touch panel and new functions. It is 2.3 kilograms and portable with its own two bottles for water resources. We can have two liquid choices and switch to the one we want to use.

Functions：
For button R is Rinse. Step on the pedal only solution comes out. Button P, Purge comes out solution for 2 minutes without pedal. Button T, Turbo means it’s been step to the stronger mode. In the middle is a lock button to make sure it won’t be switched unintentionally. After we finish our practice, we remove our insert and we can press Purge, switch to water bottle to let water go through our scaler and clean it. And then take apart our handpiece sleeve, which can be autoclaved less than 135 Celsius. And our hand piece accepts both 25 and 30 kilohertz scaler inserts for internal and external water flow.

PS-1 is piezo type of ultrasonic scaler. It is 2.2 kg and can be moved with a suitable water resource. Each device attached a small tip wrench, which used to change tips more convenient. Turn on the device, check water quantity and adjust the power of scaler. It has 3 modes for General scaling, Endodontic and Periodontal procedures. It features on with and without water during operation. This device can be used without water but maximum only for 5 minutes, otherwise the temperature of devise will be too high and costs some damages. In the beginning of operation, the liquid needs a while to flow through the tube. After it comes out, it’ll be good to use.

The Dental Digital Sensor RXS 1000 is intended to acquire real-time, clinical digital intraoral X-ray images using a solid-state imaging sensor. The cable can be separated. This system consists of the CMOS sensor and software for image display. This system senses the onset of the X-ray exposure (such as Portable X-Ray) and automatically acquires and save the image data to a PC (software).

Feature
▪ USB 3.0 Interface
▪ Pixel size: 20 x 20 μm
▪ Image size: 30 x 20 mm
▪ Resolution: 1500 x 1000 pixels

Indication for Use
This Dental Digital Sensor RXS 1000 is intended to be used by dentists and dental technicians diagnostic diseases of the teeth, jaw and oral structures. Its use is intended for adult subjects.

Contact duration of applied part
▪ Sensor (Contact Duration: Less than 1 min)

Contact area of applied part
▪ Sensor Contact area: Less than 42mm X 26.2mm (Size 1)

Our X-ray is portable with a touch panel, which has certificates for both FDA and CE. With them let this product has a good quality guarantee. You can take this on your hand as a camera. With this protected box is about 4 kilograms. Convenient for using or movement. Its modes have some selections. First button choose child or adult mode. Second button choose the position of teeth, front teeth, molars or bitewing. The third button choosing film, PSP(Phosphor Plates) or digital sensor. Our X-ray accepts these three kinds of medium. So we turn on the power, check its battery status and choose your modes. Or you can set the time by yourself. Maximum 2 seconds and shortest one is 0.02 second.

1000E DUAL features on gun shape holding. It only weights 200 gram per set. It has a charger let curing light stand on it save while charging. Each time full charged can be used for 3 hours. This light guide is free rotatable. Inside it has 4 LED lamps and combines 3 blue lights and 1 ultra light for wavelength range of 390~480nm. High light-energy output for 2,100 megawatt. Here we also have a light checker to make sure its light range is strong enough. As you can see here’s a panel for checking time and modes. This setting button controls time and mode button control 4 modes, low and ramp up for 5 or 10 seconds; high and cycle for 1 or 2 or 3 seconds.

Q4 has only one kind of LED lamp and it only weights 155 gram. Light-energy output for 1,400 megawatt. Undetachable battery full charged for 3 hours using. The charger let curing light stand in it save, however, for emergency use you can also charge it while using. But we not suggest you to do that often. Q4 only has 2 modes. As you can see this panel, H as high mode for 3, 5 or 10 seconds; the other is ramp up for 10 seconds.

Q6 NLG is a pen type curing light. It is 140 g, Light-energy output for 2000 to 2,200 megawatt. It has 3 modes: high for 3 seconds, low for 10 seconds and ramp up for 5 seconds. It has medal surface and no panel to check seconds and already set by buttons. Q6NLG has no angles for its light guide, thus it’s more comfortable for patients while curing molars.

Tray is a drawer type curing box with 3.3 kilograms. The size is smaller but its capacity for inside is bigger than LQ BOX because there’s no turntable. It has 12 LED lamps for only one kind light wavelength 405 nm. It can be customized if you need another light wavelength 460 nanometers.

This panel shows the time and mode buttons. A/B/C can be set by users. If you set A as 5 minutes, next time you can just press this button to start without setting. Here are plus and minus buttons to set the time. Each time you press will be 10 seconds and the longest time can be 9 minutes 50 second. If you want, it can be customized to hours and minutes. Each time can add 10 minutes to 9 hours 50 minutes.

This is LQ Box, a door type curing box with 6.5 kilograms. It has 36 LED lamps with at least 2 kinds of light wavelengths. Three lamps for one set and they can be customized for your needing. Normally we have 9 lamps for 405 nanometers, 27 lamps for 460 nanometers. It has a turntable and it spins during curing, and the surface for inside is made from medal so that the project be cured every side. This door type curing box has a safety switch to protect users from LED lights. It needs to be closed to start the device.

This panel shows the time and mode buttons. A/B/C can be set by users. If you set A as 5 minutes, next time you can just press this button to start without setting. Here are plus and minus buttons to set the time. Each time you press will be 10 seconds and the longest time can be 9 minutes 50 second. If you want, it can be customized to hours and minutes. Each time can add 10 minutes to 9 hours 50 minutes.

LQ box III, its capacity is 3 times of LQ box, a larger size to cure more projects at the same time. The differences are the fan, turntable and LED quantity. Its fan is on the side and it has two turntables can switch. These turntables are made by plastic with two different highs. The higher one let the project closer to the light. And it has 42 LED lamps, which also can be customized with different light wavelengths.

This panel shows the time and mode buttons. A/B/C can be set by users. If you set A as 5 minutes, next time you can just press this button to start without setting. Here are plus and minus buttons to set the time. Each time you press will be 10 seconds and the longest time can be 9 minutes 50 second. If you want, it can be customized to hours and minutes. Each time can add 10 minutes to 9 hours 50 minutes.